Canon EOS-1Ds Mark IICanon upgrades their "ultimate" d-SLR with 16.7 megapixels of resolution and significant performance improvements.<<Design :(Previous) | (Next): Sensor, Noise Reduction, and Optics>> Page 5:ViewfinderReview First Posted: 9/26/2005 |
Viewfinder
A TTL (Through The Lens) optical viewfinder is the sole mechanism for composing images on the Canon EOS-1Ds Mark II, as the 2.0-inch LCD monitor is purely for image review and menu navigation. (This is typical of most SLRs, because by nature the light path is either through the eyepiece or onto the CCD, with no provision for a "live" LCD viewfinder display.) Fortunately, the optical viewfinder on the Mark II offers a true 100 percent field of view, a relative rarity, even among high-end SLRs. The optical viewfinder has a glass pentaprism design, using a mirror to reflect the view from the lens, just as in a traditional SLR viewfinder design. A full information overlay along the bottom and right of the viewfinder window reports the current exposure settings, including shutter speed, aperture, exposure compensation, and ISO, among other information. A circular black outline at the center of the viewfinder window indicates the central spot-metering area, (although as I'll explain later, the Mark II is capable of spot metering at a number of locations within the field of view). A large, black elliptical outline marks the boundaries of the autofocus area. A total of 45 discrete autofocus sensors are distributed within this ellipse, and may be used singly or in combination as I'll describe later, in the "Optics" section of this review. Active AF points are normally invisible, illuminating red when the Shutter button is half-pressed and focus is achieved at one or more of the points.
The amount of information conveyed by the 1Ds Mark II's viewfinder readout is quite impressive, all the more so because the display is actually quite uncluttered and easy to understand. The illustration below (courtesy Canon USA) shows all the internal viewfinder displays and their functions. (Readers familiar with the EOS-1v film SLR or the previous EOS-1Ds will immediately recognize this display as being the same one used on those cameras.)
On the left side of the viewfinder eyepiece is a diopter adjustment dial, which corrects the viewfinder display from -3.0 to +1.0 diopter units to accommodate eyeglass wearers. The viewfinder has a moderately high eye point, meaning that the view should be reasonably clear, even with fairly thick eyeglasses. (In addition to the rather wide range of diopter adjustments available on-camera, Canon also offers dioptric correction lenses for the viewfinder ranging from -4 to +3 diopters in 10 steps. These clip on externally, and act in addition to the built-in diopter adjustment, for a total range of -7 to +4 diopters. If you can see well enough to pick up the camera, you should be able to see through the viewfinder!) Nine interchangeable focusing screens are available for the 1Ds Mark II. On the right side of the viewfinder eyepiece is a small lever that opens and closes a shutter behind the eyepiece. This prevents any additional light from filtering into the camera through the viewfinder eyepiece during long exposures on a tripod. The 1Ds Mark II also features a removable eyecup that fits over the viewfinder eyepiece, handy for high ambient light environments.
The 2.0-inch, TFT color LCD monitor is used only for image playback and menu viewing, and is made up of approximately 230,000 pixels. A brightness control offers five brightness levels, helpful for improving viewing in excessively dark or bright conditions. Images can be displayed with or without the relevant image information, and the 1Ds Mark II offers four- or nine-image index display modes. A very useful feature is the optional Highlight Alert, which flashes overexposed sections of the image gray/white during playback. An optional histogram display is also available, which is handy for assessing overall exposure, though I've personally found the blinking highlight display much more useful for showing where I've blown out highlights. (The problem with a histogram display is that blown highlights usually represent only a small percentage of overall image area, meaning it's hard to pick them up on the histogram readout. A blinking area on the LCD playback display is pretty hard to miss.)
The RGB Histogram also displays individual histograms, stacked one atop the other, one for each color channel.
A zoomed playback, via the Magnify and Reduce buttons on the camera's rear panel, is handy for checking fine framing details, or even for checking focus and depth of field. The 1Ds Mark II offers magnification from 1.5x to 10x. The 10x magnification level in particular is very useful for checking focus and depth of field.
Active Mirror Technology
The Canon 1Ds Mark II employs the "Active Mirror Control" technology that also appeared on the earlier members of the 1D line as well. It turns out that in normal situations, even the bounce of the mirror as it settles back into position after each shot would prevent frame rates this high. To overcome this, Canon developed "Active Mirror" technology for the EOS-1v model, which uses active drive electronics to damp out mirror vibrations in half the time that would be required otherwise. The sheer shot-to-shot speed of Active Mirror technology is only part of the equation though -- because the mirror moves so fast, the viewfinder blackout time between exposures is reduced to only 45 milliseconds. The viewfinder remains very usable, even when the shutter is clattering away at the maximum frame rate. Quite impressive, especially when you consider that the mirror is really a two piece design, with a big half-mirror that allows light through for the smaller sub-mirror behind it that reflects light down to the AF sensors below.
Follow Imaging Resource: